Quizzes for exam 1

How often should a denture be refitted?

Bone shrinks/ resorbs in what two directions?

To resurface the tissue side of a denture with new material so it will fit the tissue and remaining bone structure more accurately is a process known as a/an:

To replace the entire denture base material while maintaining occlusal relations of the artificial teeth is a process known as a/an:

What type of material is typically used for hard relines?

What are the two reasons for using a resilient denture base liner?

Which of the following soft liner materials is the most truly elastic?

The principal use of this resilient denture liner is in a cleft palate prostheses.

This soft liner may be used against fresh acrylic during initial processing of a new denture, or it can

be cured against and existing denture,

Which soft liner material offers easy polishing and finishing?

What are the two types of Acrylic denture repairs?

T/F. Soft Liner material may be temporary or permanent.

T/F. Denture relines are typically a same day service.

T/F. When heat curing a reline, be sure to boil for 30 minutes to guarantee proper bonding to old denture acrylic.

T/F. Immediate dentures will allow the patient to delay the need for a reline for longer than 4 years.

T/F. As much as 60% of bone can be lost in the first year after tooth loss.

The reline can represent a solution to two problems, and one or both problems can exist at the same time, what are these two problems?

work order should be as detailed as possible and should include the following: (6 points)

One of the key elements to a successful relationship between a dentist and a dental lab is what?

What must be supplied to the dental lab before any work is done?

DAMAS required the retention of work authorizations for how man years?

The FDA requires the retention of work authorizations for a minimum of how many years?

What are two ways you can strengthen the laboratory and dentist relationship?

T/F. Work on a restoration may not be started or completed before a work authorization has been issued

T/F. All state dental practice laws specify the functions that the dentist may perform and the conditions under which he or she may perform them

T/F. The dental technician should provide the dental office with accurate impressions and detailed procedure authorizations.

Briefly explain receiver-oriented communication.

What does NADL stand for:

What does NBC stand for:

What does AlDL stand for:

What does CODA stand for:

Which organization do you get certified though to become a CDT?

what does DAMAS stands for:

SDS stands for what:

OSHA stands for what:

GHS stands for what:

How many sections are there ?

When completing your chemical hazardous ingredient list, what section of the SDS must be checked to find the hazardous ingredients?

In which SDS section are you most likely to find the pictograms and Hazard statements?

One of our lab managers is pregnant, where do we look in the SDS to make sure we are using proper PPE and engineering controls to minimize her exposure to the chemicals we use?

In which SDS section will you find the first aid measures needed if someone is exposed to the chemical?

New products were just delivered, where in the SDS would you find the information on how to properly handle and store the new chemicals?

Which of the following are required on the label of a secondary container: Circle all that apply

T/F. The signal word Danger is used for less severe hazards

T/F. All secondary containers must be labeled each use.

T/F. There are 16 sections in the SDS.

T/F. 4 is a minor hazard under GHS but 4 under NFPA is a Severe Hazard

Exploding Bomb

Flame

Flame Over Circle

Glass Cylinder

Corrosion

Skull and Crossbones

Exclamation Mark

Health Hazard

Environment

Transport Pictograms

Section 1-16

Section 1

Section 2

Section 3

Section 4

Section 5

Section 6

Section 7

Section 8

Section 9

Section 10

Section 11

Section 12

Section 13

Section 14

Section 15

Section 16